X-Plane 9.70

NightFlash · Oct 14, 2012

Есть вопрос.
Дано:
Две машины под MacOsX.
Два X-Plane 9.70.
Локальная сеть.

Надо:
Настроить X-Plane так, чтобы можно было летать экипажем через локалку на одном самолёте с полным функционалом управления с обеих машин.

Пока получается только вывести на одну из машин внешний вид.
Управлять выходит только с одной.

Подскажите, плиз, где копать.

Спрашивал на русском форуме, но там дали ответ тот, который я уже сам нашёл:

Now, if you do NOT want to run ONE copy of X-Plane at 2048x768 with TWO monitors sprouting out of that one computer to do your copilot panel, you can use a DIFFERENT computer for the copilot-side panel.

Do it this way:

Get 2 computers and 2 copies of X-Plane, and a single crossover Ethernet cable, or a pair of Ethernet cables and an Ethernet hub.

Install X-Plane on each computer.

Connect the computers to form a simple LAN, as you always would in Mac or Windows, as the case may be.

Make a cool airplane, with the PILOTS SIDE INSTRUMENT PANEL just the way you like it. Save it with a name like: "coolplane.acf"
when you are done, simply make a copy of the airplane, and name the copy "coolplane_copilot.acf". Notice you just added the "_copilot.acf" on the end.

Save that copilot's-side airplane in the same folder as the pilot's-side plane.

Open the "coolplane_copilot.acf" in Plane-Maker, and tweak the instrument panel all out to be perfect for the co-pilots side.

Now you have 2 copies of the same plane, each with its own instrument panel, and the names "coolplane.acf" and "coolplane_copilot.acf".
The .acf files are in the same folder, right beside each other.

Now simply copy that whole aircraft folder from one of your computers over to the other, putting the aircraft folder in the same place in the second (copilots) copy of X-Plane.

Now simply fire up X-Plane on each computer, go to the SETTINGS menu, and then to the DATA INPUT OUTPUT window on each computer, and select INET 2 tab.

Check the IP ADDRESS OF EXTRA VISUAL/COCKPIT #1 (THIS IS MASTER) button on that computer, and enter the IP address of the copilot's machine.

On the COPILOT'S machine, check the IP ADDRESS OF MASTER MACHINE (THIS IS EXTRA COCKPIT), and enter the IP address of the pilot's machine.

Now, on the lower left, click on the 'aircraft name reading suffix' and enter (can you guess it? if you are smart, you should) "_copilot".
That means that NO MATTER WHAT PLANE YOU OPEN ON THE PILOTS MACHINE, this computer will add "_copilot" to the name of the plane that it tries to open!
Now, on the PILOTS machine, open the "coolplane.acf"... if you set everything up right, then the pilots machine will send all the appropriate data to the copilot's machine (because you checked the "ip address of external..." box), the copilots machine will get the message (because you checked the "ip address of master..." box) and the copilot's machine will apply the name "_copilot" to the aircraft name (because of the name suffix you entered), and open the copilot’s plane on the copilot’s machine. A plane that has a copilot's instrument panel, if you did your job in Plane-Maker.
Click to expand...

Меня смущает именно вот это вот "Make a cool airplane, with the PILOTS SIDE INSTRUMENT PANEL" и "Open the "coolplane_copilot.acf" in Plane-Maker, and tweak the instrument panel all out to be perfect for the co-pilots side".

Это вот как?
Я просто с Plane Maker'ом не сталкивался ни разу, и как там разграничивать эти Pilot и Copilot side — не знаю...
Тобишь, открываю я себе свой 737 в Плэйнмейкере — иии..?
Внятного мануала к нему я не нашёл, к сожалению...

Log in or Sign up

X-Plane 9.70

NightFlash Well-Known Member

Log in or Sign up

X-Plane 9.70

NightFlash Well-Known Member

Useful Searches